Product Data Sheet
September 2017
212-60-080, Rev J
Paine
™
212-60-080 Series Pressure Transducer
VDC, Differential, +121 °C, Ranges to 5,000 PSID (344 BAR)
The Paine 212-60-080 Differential Series is temperature compensated and a 0–5 VDC output, full line
differential pressure sensor.
With two separate sensing elements to measure the pressure at the input ports, each sensor has two
strain gage legs. These two sensors are connected to provide a fully balanced bridge. This sensing
method provides an accurate output directly proportional to the pressure difference at the two ports.
Featuring built-in electronics to eliminate the need for separate sensors and amplifiers, the Paine
212-60-080 Series is designed for dependable and long-term pressure measurement in a small/light
weight (3 oz) manifold style mounting package.
2
Paine 212-60-080
September 2017
Emerson.com/Paine
Potential applications
Actuator and propulsion controls
Industrial hydraulic and pneumatic controls
Automotive test systems
Vehicle steering control systems
Fuel pressure monitoring
Positioning systems
Robotic hydraulic controls
Valve pressure control
Features
Thermal zero shift: ±0.02% of Full Scale (F.S.) per °F
maximum
Thermal sensitivity shift: ±0.02% of F.S. per °F maximum
Output: VDC
Operating temperature: –40 to +250 °F (0 to +121 °C)
Pressure range: ±500 to ±5,000 psid (34 to 344 bar)
Operating media: Any compatible with 300 series CRES,
Buna-N-Rubber, 2024-T351 AL, and 15-5 PH CRES
Pressure fitting: Manifold mounting per MIL-G-5514, Type II,
Class 2. O-rings (2) MS28775-008 are supplied with each
transducer.
Specifications
Calibration: Calibration certificates are supplied with each unit
and available online.
Performance
Thermal zero shift: ±0.02% of F.S. output per °F maximum
Thermal sensitivity shift: 0.02% of F.S. per °F maximum
Output at zero differential pressure: 0.0 ± 0.1 VDC = E
o
over
calibrated temperature range
Output at positive rated pressure (P1 > P2):
+5.0 ± 0.1 VDC = E
p
Output at negative rated pressure (P2 > P1):
- (E
p
– 2 E
o
) ± 0.1 VDC
Static error band (non-linearity and hysteresis combined):
See “Pressure Table” on page 3.
Operating temperature: –40 to +250 °F (0 to +121 °C)
Environmental
Positive excitation: 11 to 40 VDC, 20 mA maximum
Negative excitation: –6 to –15 VDC, 5 mA maximum
Output current: 50 kΩ maximum load, short circuit protection
Output ripple: 70 mV peak to peak (typical) 0–1 kHz bandwidth
Electrical connections: Six pin bayonet locking electrical
connector. Mates with M83723-75R10066 type connector, not
supplied with unit.
Contents
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Solutions
Fast response time
Compact design
High shock and vibration design
Port adapters available
Port adapters and accessories
available
3
Paine 212-60-080
September 2017
Emerson.com/Paine
Mechanical
Pressure range: Contact factory for additional pressure ranges.
Operating media: Any compatible with 300 series CRES,
Buna-N-Rubber, 2024-T351 AL and 15-5 PH CRES.
Pressure fitting: Manifold mounting per MIL-G-5514, Type II,
Class 2. O-rings (2) MS28775-008 are supplied with each
transducer.
Electrical
Excitation: 10 VDC
Input resistance: 350 ± 70 Ω
Output resistance: 350 ± 35 Ω
Electrical connections: Four pin bayonet locking electrical
connector. Mates with MS3116-8-4S. (P/N: 247-99-100-01 sold
separately).
Table 1. Pressure Table
Standard part
number
Pressure range
PSID (BAR)
Proof pressure
PSID (BAR)
Burst pressure
PSID (BAR)
Static error band
(BSLM)
212-60-080-01 ±500 (34) ±850 (58) ±1,250 (86) ±1.0% F.S.
212-60-080-02 ±1,000 (68) ±1,700 (117) ±2,500 (172) ±0.75% F.S.
212-60-080-03 ±3,000 (103) ±5,100 (351) ±7,500 (517) ±0.5% F.S.
212-60-080-04 ±5,000 (137) ±8,500 (586) ±12,500 (861) ±0.5% F.S.
4
Paine 212-60-080
September 2017
Emerson.com/Paine
Dimensional Drawings
Figure 1. Paine 212-60-080 Series
A. Pressure port manifold mounting per MIL-G-5514
B.
∅.125/.130 through four places
Dimensions are shown in inches.
.942
.932
.65 max
.10 max
1.57 max
1.13 max
.317
.307
P1 P2
1.895
1.865
.492 .516 .682
1.500
.219
.438
.700
.350
.375
1
2
34
5
6
AB
Connections
PIN Function
1+ Excitation
2 Output (+ if P1 > P2)
3 Output return
4 Excitation return
5 Do not connect
6- Excitation
5
Paine 212-60-080
September 2017
Emerson.com/Paine
This page is intentionally left blank.
Product Data Sheet
September 2017
Paine 212-60-080
212-60-080, Rev J
Rosemount Specialty Product LLC
Emerson Automation Solutions
5545 Nelpar Drive
East Wenatchee, WA 98822, USA
+1 509 881 2100
+1 509 881 2115
Paine.Products@Emerson.com
Linkedin.com/company/Emerson-Automation-Solutions
Twitter.com/Rosemount_News
Facebook.com/Rosemount
Youtube.com/user/RosemountMeasurement
Google.com/+RosemountMeasurement
Standard Terms and Conditions of Sale can be found on the Terms and
Conditions of Sale page.
The Emerson logo is a trademark and service mark of Emerson Electric Co.
The Paine brand and Paine logotype are trademarks of Emerson Electric Co.
All other marks are the property of their respective owners.
© 2017 Emerson. All rights reserved.
